Home > Error Code > Ultrium 4 Error Code 8

Ultrium 4 Error Code 8

Contents

Upgrade the Autoloader firmware to the latest release. more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science To remove a stuck tape from a storage slot: If the operator control panel or the remote management interface is still operational: Move the tapes from the drives to the magazines Not the answer you're looking for? Check This Out

top top Error codes If an error occurs during operation of the device, the device stops the current operation and displays an error code on the LCD screen. NOTE: Many backup applications use their own drivers. Do not backup when the database is in heavy use. An LTO-4 tape drive is unable to sustain maximum transfer speeds with 2:1 compressible data. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ibm Lto 5 Tape Drive Error Code 6

Upgrade to Fibre Channel if using LTO-3 or LTO-4 tape drives. Verify that your HBA is supported by the host computer and qualified with the Autoloader. However, a sequential/disk image backup might not allow you to restore individual files or the restore process will be very slow.

Do not use cartridges that are incompatible with the tape drive. When fully used and assuming that the connection to the disks does not force the speed to a lower parallel SCSI type, an Ultra 2 (80) connection barely provides enough bandwidth http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/powervault-lto4-120hh?driverId=X939P&osCode=WNET&fileId=3283341798&languageCode=en&categoryId=TH%C2%A0%C2%A0; Please let us know if you have any other questions. 0 This discussion has been inactive for over a year. Dell Tape Drive Error Code 7 LTO-3, LTO-4: POOR.

Also if you have the diagnostic tool you can run a test on the drive to see if it gives anymore issues.  Here is a link to download the firmware and Ibm Tape Library Error Codes Native backup applications based on tar, cpio, NT Backup, etc. Check all SCSI and power connections and confirm that the unit is attached to a valid SCSI SE or LVDS bus. Fourth code - sub-code-specific information for factory use only Figure 9: Support: Autoloader logs page top Finding error code information on an L&TT support ticket or report An L&TT support ticket

Everything shows all events. Ibm Ts3500 Error Codes Based on the extent of the detection problem, check the following: If neither the application software nor operating system detects the tape drive, or they do not detect both the tape If the application software or operating system does not communicate with the device after installation, determine the extent of the detection problem. Inventory problems Problem Solution The inventory labels the cartridge Full instead of showing its bar code Verify that the label is an HP label.

Ibm Tape Library Error Codes

For Ultra 320 or multiple devices on a bus, the maximum combined internal/external length is 40 feet (12 meters). http://serverfault.com/questions/338532/dell-powervault-lto4-120-drive-displays-error-6-on-the-drive-display The available logs are: Error Trace, Informational Trace, Warning Trace, Configuration Change Trace, and Standard Trace. Ibm Lto 5 Tape Drive Error Code 6 If the Autoloader is detected by the operating system, but not by the application software: Refer to the documentation included with your backup application for instructions on how to verify proper Tape Drive Or Rs-422 Error Check cleaning tape and exchange if necessary.

A cartridge should be acclimated for at least 24 hours before being used, particularly if it has been stored at a substantially different temperature or level of humidity than the device. his comment is here Find the performance impact of your system's Autoloader connection in Performance impact of various Autoloader connections Performance impact of various Autoloader connections Connection type Performance impact Recommendations Parallel SCSI: Ultra 320 The SCSI cable length might be too long. Order of operations in statistics Can a PC change Backgrounds mid-campaign? Ibm 3584 Error Codes

Make sure that the proper device driver is installed for the SCSI host adapter. The system returned: (22) Invalid argument The remote host or network may be down. LTO-3: MARGINAL. this contact form The disadvantage is that backup and restore operations work on an entire disk, partition, or LUN.

Check if the fan is operational and not obstructed F0 Drive exceeded temperature specification Check ambient temperature conditions and fans F1 Autoloader controller lost communication with the drive Re-seat the tape Ibm Ultrium-hh3 Status Lights For reliable operation, do not use a SAS cable longer than six meters. Clean the tape drive.

Make sure you are using data and cleaning cartridges that are compatible with the drive and model of the device (see the Tape cartridges section in Tape Cartridges and Magazines ).

Make sure that you cycle power on the device after changing the SCSI ID. Review the manuals for the other devices on the SCSI bus or the operating system to determine which SCSI IDs are currently in use. The code after LIB/ERR (80 in the example) will be 80 or 40. 80 indicates a hard error, 40 indicates a soft error. Dell Tape Drive Error Codes When fully used and assuming that the connection to the disks does not force the speed to a lower parallel SCSI type, an Ultra 160 connection can provide enough bandwidth for

Also, you're sure it's the LTO drive displaying the number, not a separate device in the top bay (the T300s have a completely separate display in the top bay on the The report is easier to read, but must be generated and read on the host computer. Who is spreading the rumour that Santa isn't real? http://dwoptimize.com/error-code/ultrium-3-error-code-5.html Make sure the backup server has enough memory to handle the bandwidth of the backup or restore.

top top Connection from the host server to the Autoloader For the best performance, the connection from the host server to the Autoloader must have enough bandwidth to provide enough data Figure 5: Error code in the OCP Error Log The code 9B is the main error code, 37 is the error sub-code, and 31 is sub-code specific information for factory use Make sure the power button on the front panel has been pressed, and the green READY LED is lit. Media problems Problem Solution Cleaning or data cartridge incompatible with drive.

Upgrade the Autoloader firmware to the latest release.