Home > Error Code > Unix Tcp/ip Error Codes

Unix Tcp/ip Error Codes

Contents

Call your system administrator. 88 EDOTDOT All A cross-mount point was detected. Communication protocol being used: protocol . ENETDOWN 69 228 127 127 The network is down. Increase the number of allocate sockets, or decrease the number of sockets used by your program. 2009 ESOCKETNOTDEFINED REXX The socket is not defined. http://dwoptimize.com/error-code/unix-cat-error.html

The default value is two hours. Correct the command parameter. WSAENETUNREACH (10051): The network can't be reached from this host at this time. The SetAD_eye1 value is not valid.

Tcp/ip Error Codes List

Correct the function address parameter. 49 EADDRNOTAVAIL Multicast APIs The specified multicast address, interface address, or interface index is not correct. When using a DOS TCP/IP product (IBM TCP/IP for DOS, FTP TCP/IP for DOS, Novell TCP/IP for DOS), the following is a list of errnos which the user may encounter most Correct the protocol parameter. 44 ESOCKTNOSUPPORT All The specified socket type is not supported. Reconnect with the peer. 32 EPIPE IOCTL (SIOCTTLSCTL requesting TTLS_INIT_ CONNECTION, TTLS_RESET_CIPHER, or TTLS_STOP_ CONNECTION) The TCP connection is not in the established state.

Only call Setibmopt() once. 38 ENOTSOCK All A socket operation was requested on a nonsocket connection. ENETRESET (10052): The network has dropped the connection on reset. ADO timeout, VB timeout. Tcp Error Code SOCEMFILE (10024): Too many open files.

Check specified IOCTL() values. 26 ETXTBSY All A text data set is busy. Terms Privacy Security Status Help You can't perform that action at this time. Request TTLS_ALLOW_ HSTIMEOUT only when the security type is TTLS_SEC_SERVER or higher and the HandshakeTimeout is not 0. 87 EMULTIHOP All A multihop address link was attempted. https://www.ibm.com/support/knowledgecenter/SSLTBW_1.13.0/com.ibm.zos.r13.cs3cod0/syserret.htm Check status of the device attempting to access. 7 E2BIG All The argument list is too long.

The default range is 0-49. Errno For example, let's look up errno 79 from the message above plus a few other codes: sh> errno 79 EMFILE 27 errno: V1.2 lookup on AIX 6100-09-01-1341 (powerpc) errno 79: ECONNREFUSED Call your system administrator. 71 EREMOTE All There are too many levels of remote in the path. This indicates an z/OS® UNIX® process initialization failure.

Tcp Socket Error Codes

Call your system administrator. 76 EBADMSG All The system cannot read the message. navigate here Usually this is network issue Check TCPIP's KEEPALIVE setting see note1 Windows AIX SUN HP Linux Short Name Action Plan 10048 67 125 226 98 EADDRINUSE The specified address already in Tcp/ip Error Codes List This error is generated by the client stub code. Ioctl Error Codes Always be sure to look up errno values on the same kind of system where they were reported.

Correct the AF or the FAMILY. 5 EIO All An I/O error occurred. check over here Ensure user ID has authority for the specified operation. 1015 EIBMBADCONNECTIONMATCH All A connection token that is not valid was detected. Check the maximum sockets specified in MAXDESC(). 25 ENOTTY All An incorrect device call was specified. Check the offset parameter for seek operation. 30 EROFS All The data set system is Read only. Socket Error Codes Linux

EADDRINUSE (10048): The specified address is already in use. Record these values and tell the systems administrator. Location where the error was detected: "192.168.1.200". his comment is here EXPLANATION: An unexpected error occurred in communications.

Embed Share Copy sharable URL for this gist. Unix TCP/IP errnos. WSAEWOULDBLOCK (10035): The socket is marked as non-blocking and the operation would block.

ENOTCONN (10057): The socket is not connected.

E.g. Request to retrieve the hostname's IP address from the name server failed. Generated Thu, 08 Dec 2016 06:14:31 GMT by s_wx1193 (squid/3.5.20) In example below it is 15 minutes.

For FREEADDRINFO, the resolver storage does not exist. When using TCP/IP or IPX/SPX under Windows 3.1, Windows 95, or Windows NT, the following is a list of error codes which the user may encounter most frequently. Check and correct function parameters. 34 ERANGE All The result is too large. http://dwoptimize.com/error-code/unix-error-code-13.html Call your system administrator. 55 ENOBUFS Send Sendto Write Not enough buffer space is available to send the new message.

Call your MVS system programmer. 2017 EIPADDRNOTFOUND REXX Address not found. Check policy and add ApplicationControlled On if the application should be permitted to issue the controlled SIOCTTLSCTL functions. 14 EFAULT All An incorrect storage address or length was specified. Check file name and if it exists. 20 ENOTDIR All The specified directory is not a directory. A timeout or ECB value can also be added to avoid the select/selectex from waiting indefinitely. 79 ENOLCK All No record locks are available.

Correct the SOCTYPE. 9 EBADF All An incorrect socket descriptor was specified. WSATRY_AGAIN (11002): Host not found.